manualshive.com logo in svg

MUTOH VJ-1628TD, Operation Manual

Share
Download
MUTOH VJ-1628TD Operation Manual Download Page 63

VJ-1628TD, VJ-2628TD OPERATION MANUAL

3 Before using

3-31

NOTE

• Load the roll media into the printer before setting it to the take-up unit.

3.5.1.1 Loading roll media into the printer

Follow the procedure below to set the roll media to the take-up unit.

1. Turn the printer ON.

CAUTION

• Do not operate the media loading lever during initial operation.

The print head portion may touch the pressurizing roller portion, and cause a 
malfunction.

•

The printer starts the initializing operation.

•

"Media End" is displayed on the operation panel.

2. From the Setup menu display, display the "Media Set" menu and confirm that the setting is "Roll".

4.3.1 Menu setup procedure

3. From the Setup menu, display the "Take-up" menu and set to "Type1".

5.1.7 Take-up menu

4. From the Setup menu display, display "Vacuum Fan" menu and confirm that the setting is "OFF".

5.1.1.1.3 Vacuum Fan menu

NOTE

• Do not perform this step when printing on the transfer paper.

Summary of Contents for VJ-1628TD



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands