MUTOH VJ-1628TD Operation Manual Download Page 226

Page: 226 / 274

6 Maintenance

VJ-1628TD, VJ-2628TD OPERATION MANUAL

6-20

4. Press the [>] key on the operation panel to select the cleaning mode.

5. Press the [Cleaning] key on the operation panel for at least two seconds.

•

If the head height is set to High, "Set Height to Low" is displayed on the operation panel.
Change the head height to Low.

4.2.5 Head height adjustment

•

Start Head cleaning.

•

"Cleaning **%" is displayed on the operation panel.

•

After Head cleaning is complete, the operation panel shifts to Normal.

NOTE

• If blurs or lacking parts in printed media do not disappear with one time of Head cleaning,

perform Strong cleaning.

• If blurs or lacking parts in printed media do not disappear with several times of Head cleaning,

refer to "7 Troubleshooting", and take appropriate measures.

Summary of Contents for VJ-1628TD



















































































































































































































































































Search results

Summary of Contents for VJ-1628TD

Reviews:

Brands by name

Popular brands

MUTOH VJ-1628TD, Operation Manual

Search results

Summary of Contents for VJ-1628TD

Reviews:

Brands by name

Popular brands