manualshive.com logo in svg

MUTOH VJ-1628TD, Operation Manual

Share
Download
MUTOH VJ-1628TD Operation Manual Download Page 199

VJ-1628TD, VJ-2628TD OPERATION MANUAL

5 Panel setup menu

5-35

5.4

Cleaning menu

Performs head cleaning.

TIP

•

Head cleaning can be operated when the printer is Normal.
Refer to the following for operation procedures.

6.2.3 Head cleaning

Setup item

Description

Short

Discharges smaller amount of ink compared to "Normal".

Normal

Select this mode normally.

Long

Discharges larger amount of ink compare to "Normal".
Used when the print head does not improve by normal Head cleaning.

Little Charge

Refills a small amount of ink.
Charge a small amount of ink when printing is not stable after ink replenishment.

3.4 Installing ink cartridges

—

• [Enter] key:

"Cleaning **%" is displayed on the operation panel and Head cleaning starts.
Progress on the Head cleaning is displayed in % on the operation panel.
However, if the head height set to High,
"Set Height to Low" is displayed on the operation panel.
Change the head height to Low.

4.2.5 Head height adjustment

• [Cancel] key: shifts to the previous menu.

5 Panel setup menu

Summary of Contents for VJ-1628TD



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands