MUTOH VJ-1628TD Operation Manual Download Page 237

Page: 237 / 274

VJ-1628TD, VJ-2628TD OPERATION MANUAL

6 Maintenance

6-31

4. Loosen the four adjusters of the stand as shown in the next illustration.

5. Move the printer.

NOTE

• The casters supplied with the dedicated stand are manufactured for little movement in flat

indoor areas, not for transporting equipment.

(2) Reinstalling

After moving the printer, follow the procedure below to set it ready for use.

1. Select a suitable place for installation.

Installation manual

2. Move and install the printer to the location.

3. Attach cables, such as the power cable.

3.1 Power cable connection
3.8 Connecting the printer to PC

No.

Name

Adjusters

Stands

Summary of Contents for VJ-1628TD



















































































































































































































































































Search results

Summary of Contents for VJ-1628TD

Reviews:

Brands by name

Popular brands

MUTOH VJ-1628TD, Operation Manual

Search results

Summary of Contents for VJ-1628TD

Reviews:

Brands by name

Popular brands