Rockhopper 38 – Maintenance Manual
169
AP-74038, Rev. 1.1, 25/01/05
7.2.10 How to check the Power Supply Voltages / 5 V DC
Step 1 :
Turn off the power switch and open the Control Box.
(The power cable may remain connected.)
Step 2 :
With Power Board connector J001 disconnected, turn on the Power Switch and check that
+5 V ± 0.5 V is being output between pins 2 and 1 of J001.
If not, take the following steps to identify the cause:
•
Go to (How to Check the Power Supply Voltages/100 V AC or 200 V AC)
•
If the 100 V AC or 200 V AC check is normal and there is no +5 V output, replace the Power
Board.
Step 3 :
Turn off the power supply momentarily to restore the J001 connector to the Power Board. Turn
on the Power Switch and check that +5 V ±0.5 V is being output between pins 2 (GND) and 1 (+5
V) of J101 on the Main Board. If not, take the following steps to identify the cause:
•
Turn off the power supply momentarily to disconnect J110 (PANEL) from the Main Board and
check again.
If this is successful, either the Panel Board Assembly or the Panel Cable is faulty.
•
Turn off the power supply momentarily to disconnect J111 (HEAD1) and J112 (HEAD2) from
the Main Board and check again.
If this is successful, either the Head Board or the Print Head Assembly or the Y Cable
Assembly or the Head Cable Assembly or the Origin Sensor Assembly or the Paper Sensor
Assembly is faulty.
•
Turn off the power supply momentarily to take out the Extended Memory (SIMM) and check
again.
If this is successful, the Extended Memory (SIMM) is faulty.
•
Turn off the power supply momentarily to take out the Option Interface Board and check
again.
If this is successful, the Extended Memory (SIMM) is faulty.
•
Turn off the power supply momentarily to disconnect J109 (INK ID) from the Main Board and
check again.
If this is successful, the Junction Board Assembly, the Detector Assembly, the Ink ID Sensor
(either Y/M/C/K) are faulty.
•
Turn off the power supply momentarily to disconnect J105 (Waste Fluid Box Detector Switch
Assembly) from the Main Board and check again.
If this is successful, the Waste Fluid Box Detector Switch Assembly is faulty.
•
Turn off the power supply momentarily to disconnect J103 (Paper Sensor Front Assembly)
from the Main Board and check again.
If this is successful, the Paper Sensor Front Assembly is faulty.
•
Turn off the power supply momentarily to disconnect J107 (Paper Sensor Rear Assembly)
from the Main Board and check again.
If this is successful, the Paper Sensor Rear Assembly is faulty.
•
Turn off the power supply momentarily to disconnect J104 (Lever Sensor Assembly) from the
Main Board and check again.
If this is successful, the Lever Sensor Assembly is faulty.
•
Turn off the power supply momentarily to disconnect J121 (X Encoder) from the Main Board
and check again.
If this is successful, the X Motor is faulty.
Step 4 :
If there is still no +5 V output with all the above connectors disconnected,
•
Replace the DC Cable Assembly
•
Replace the Main Board.
Summary of Contents for Rockhopper 38
