Multitech MultiVOIP 400 User Manual Download Page 13

Page: 13 / 88

Chapter 1 - Introduction and Description

Specifications

•

One 1 Meg by 32 byte at 70 nanosecond SIMM is 4 Mb DRAM

Caution: SIMM speed and size cannot be mixed

•

Two Meg of flash memory

Ethernet Port

•

Single Ethernet Interface - 10Base-T (twisted pair) keyed RJ-45 connector.

Command Port

•

Single 19.2K bps asynchronous Command Port with a DB-25 female connector

Voice/Fax Channel _

•

Two RJ-11 jacks (FXO and FXS)

•

One RJ-45 jack (E&M)

Electrical/Physical

•

Voltage - 115 VAC (Standard), 240 Volts AC (Optional)

•

Frequency - 47 to 63 Hz

•

Power Consumption - 18 Watts

•

Dimensions - 3.75" high x 17.4" wide x 8" deep

8.9cm high x 44.2cm wide x 20.3cm deep

•

Weight - 7.4 pounds (3.4 kg)

Summary of Contents for MultiVOIP 400

























































































Search results

Summary of Contents for MultiVOIP 400

Reviews:

Related manuals for MultiVOIP 400

Brands by name

Popular brands

Multitech MultiVOIP 400, User Manual

Search results

Summary of Contents for MultiVOIP 400

Reviews:

Related manuals for MultiVOIP 400

Brands by name

Popular brands