Multitech MultiVOIP 400 User Manual Download Page 23

Page: 23 / 88

Chapter 3 - Software Loading and Configuration

Follow the on-screen instructions to install your MultiVOIP software.

You may choose the Destination Location of your MultiVOIP software or you can choose to

select the default destination by clicking Next.

If you click Browse, you can choose from several folders. It is recommended to choose the

default destination.

The following dialog box selects the COM port of your PC connected to the Command port of

the MultiVOIP. From the Select Port window, click on the down arrow and choose the COM
port of your PC.

Click OK to continue.

The Setup Complete dialog is displayed.

Click Finish to continue.

The following message is displayed:

Click Yes to continue.

Summary of Contents for MultiVOIP 400

























































































Search results

Summary of Contents for MultiVOIP 400

Reviews:

Related manuals for MultiVOIP 400

Brands by name

Popular brands

Multitech MultiVOIP 400, User Manual

Search results

Summary of Contents for MultiVOIP 400

Reviews:

Related manuals for MultiVOIP 400

Brands by name

Popular brands