manualshive.com logo in svg

MTU 12 V 4000 L62, Operating Instructions Manual

Share
Download
MTU 12 V 4000 L62 Operating Instructions Manual Download Page 80

152028 – Open Primary, Channel 3

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

152029 – Open Primary, Channel 4

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

152030 – Open Primary, Channel 5

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

152031 – Open Primary, Channel 6

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

152032 – Open Primary, Channel 7

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

152033 – Open Primary, Channel 8

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

152034 – Open Primary, Channel 9

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not

discharged.

1. Check cabling to ignition coil.

2. Check ignition coil.

80 | Troubleshooting | MS150033/04E 2012-07

TIM-ID: 0000017543 - 001

Summary of Contents for 12 V 4000 L62




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands