manualshive.com logo in svg

MTU 12 V 4000 L62, Operating Instructions Manual

Share
Download
MTU 12 V 4000 L62 Operating Instructions Manual Download Page 124

472 –  AL Stop SD

ZKP-Number: 

Red alarm. Engine shutdown.
Associated parameter 2.8006.593

Cause

Corrective action

Engine stop, since all shutdown

channels detect “sensor defect".

u

Combined alarm (for details, refer to the source alarm).

473 –  AL Wiring PWM_CM2

ZKP-Number: 

Red alarm. Engine shutdown.
Associated parameter 1.8004.593

Cause

Corrective action

Cable break or short circuit on

channel PWM_CM2.

u

Check cabling to bypass throttle, replace bypass throttle if

necessary.

476 – AL Crash Rec.Init Fault

ZKP-Number: 

Red alarm.
Associated parameter 1.8010.007

Cause

Corrective action

Crash recorder initialization

error.

u

Contact Service.

478 –  AL Comb. Alarm Yel (Plant)

ZKP-Number: 

Yellow alarm.
Associated parameter 2.8006.001

Cause

Corrective action

Combined alarm YELLOW from

plant.

u

Combined alarm (for details, refer to the source alarm).

479 –  AL Comb. Alarm Red (Plant)

ZKP-Number: 

Red alarm. Engine shutdown.
Associated parameter 2.8006.002

Cause

Corrective action

Combined alarm RED from

plant.

u

Combined alarm (for details, refer to the source alarm).

124 | Troubleshooting | MS150033/04E 2012-07

TIM-ID: 0000017544 - 001

Summary of Contents for 12 V 4000 L62




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands