manualshive.com logo in svg

MTU 12 V 4000 L62, Operating Instructions Manual

Share
Download
MTU 12 V 4000 L62 Operating Instructions Manual Download Page 56

112403 – LO T-Exhaust A3

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112404 – LO T-Exhaust A4

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112405 – LO T-Exhaust A5

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112406 – LO T-Exhaust A6

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

112407 – LO T-Exhaust A7

Yellow alarm. Initiated by EMU.

Cause

Corrective action

The exhaust temperature of this

cylinder is too low as compared

with the average value.

1. Check spark plug.

2. Check emission values.

3. Check ignition timing (→ Page 137).

4. Check valve drive.

56 | Troubleshooting | MS150033/04E 2012-07

TIM-ID: 0000017543 - 001

Summary of Contents for 12 V 4000 L62




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands