MR OILTAP R Installation And Commissioning Instructions Download Page 5

Page: 5 / 206

Table of contents

Maschinenfabrik Reinhausen GmbH 2015

4427410/00 EN

OILTAP® R

Fitting protective devices and drive components............................................................................. 116

5.5.1

Connecting the tap-change supervisory control (if installed)............................................................................. 116

5.5.2

Installing protective relay in piping and connecting........................................................................................... 117

5.5.3

Installing and connecting the pressure-operated relay...................................................................................... 128

5.5.4

Fitting motor-drive unit....................................................................................................................................... 131

5.5.5

Fitting bevel gear............................................................................................................................................... 131

5.5.6

Fitting drive shaft............................................................................................................................................... 132

5.5.7

Centering on-load tap-changer and motor-drive unit......................................................................................... 162

5.5.8

Installing electrics for motor-drive unit............................................................................................................... 162

Commissioning the on-load tap-changer at the transformer manufacturer's site... 163

6.1

Bleeding on-load tap-changer head and suction pipe..................................................................... 163

6.1.1

Bleeding on-load tap-changer head.................................................................................................................. 163

6.1.2

Bleeding suction pipe on pipe connection S...................................................................................................... 164

6.2

Grounding the on-load tap-changer................................................................................................. 164

6.3

Performing tests on motor-drive unit............................................................................................... 165

6.4

Performing trial tap-change operations........................................................................................... 165

6.5

High-voltage tests on the transformer............................................................................................. 166

Transporting transformer to the operating site........................................................... 168

7.1

Transport with removed drive.......................................................................................................... 168

7.2

Transport with oil fill and without oil conservator............................................................................. 168

7.3

Transport without oil fill.................................................................................................................... 169

7.3.1

Emptying oil compartment via pipe connection S.............................................................................................. 169

Commissioning the transformer at the operating site................................................ 171

8.1

Checking motor-drive unit................................................................................................................ 171

8.2

Checking protective relay................................................................................................................ 172

8.2.1

Checking protective relay (RS 2001, 2001/V, 2001/H, 2001/E, 2001/5, 2001/R, 2003).................................... 172

8.2.2

Checking protective relay (RS 2004)................................................................................................................. 172

8.3

Checking pressure monitoring device............................................................................................. 172

8.4

Filling the oil compartment of the on-load tap-changer with oil....................................................... 173

8.5

Bleeding on-load tap-changer head and suction pipe..................................................................... 176

8.5.1

Bleeding on-load tap-changer head.................................................................................................................. 176

8.5.2

Bleeding suction pipe on pipe connection S...................................................................................................... 178

8.6

Performing trial tap-change operations........................................................................................... 178

8.7

Commissioning the transformer....................................................................................................... 179

Summary of Contents for OILTAP R















































































































































































































Search results

Summary of Contents for OILTAP R

Reviews:

Brands by name

Popular brands

MR OILTAP R, Installation And Commissioning Instructions

Search results

Summary of Contents for OILTAP R

Reviews:

Brands by name

Popular brands