MR OILTAP R Installation And Commissioning Instructions Download Page 87

Page: 87 / 206

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

4427410/00 EN

OILTAP® R

Disconnect the plug connector.

Figure 89: Disconnecting plug connector

Put part B of plug connector back in bracket.

Figure 90: Placing part B of plug connector in bracket

Swivel part A of plug connector out of on-load tap-changer head in di-
rection indicated by arrow until it is between the pipe connections and
the cable cannot be damaged when pulling out the diverter switch insert.

Figure 91: Swiveling out part A of plug connector

Lifting out diverter switch insert

Loosen nuts and safety elements on carrier plate of diverter switch in-
sert.

NOTICE!

Make sure that parts do not fall into the oil compartment.

5.3.6.4

Summary of Contents for OILTAP R















































































































































































































Search results

Summary of Contents for OILTAP R

Reviews:

Brands by name

Popular brands

MR OILTAP R, Installation And Commissioning Instructions

Search results

Summary of Contents for OILTAP R

Reviews:

Brands by name

Popular brands