manualshive.com logo in svg

MR OILTAP R, Installation And Commissioning Instructions

Share
Download
MR OILTAP R Installation And Commissioning Instructions Download Page 140

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

140

4427410/00 EN

OILTAP® R

9.

NOTICE!

 After installing all drive shafts, continue cranking another 2.5

revolutions counter-clockwise on the drive shaft of the upper gear unit to
correctly complete the tap-change operation. An incomplete tap-change
operation may damage the on-load tap-changer!

10. Move on-load tap-changer back into adjustment position by turning drive

shaft clockwise. Once the adjustment position has been reached and
the diverter switch has undergone the tap-change operation, continue
cranking another 2.5 revolutions clockwise on the drive shaft of the up-
per gear unit to correctly complete the tap-change operation.

11. Check operation of all on-load tap-changers. A slight time delay is per-

mitted.

12. Check that the operating positions of all on-load tap-changer heads are

the same.

13. Fit vertical drive shaft.

Fitting vertical drive shaft

Couple drive shaft with motor-drive unit and on-load tap-changer as descri-
bed in MR operating instructions for TAPMOTION® ED.

 WARNING

The motor-drive unit may be started by accident if the motor
protective switch is not tripped!

Risk of injury from starting the motor-drive unit by accident!
► Trip motor protective switch before starting to fit the drive shafts!

5.5.6.2

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands