manualshive.com logo in svg

MR OILTAP R, Installation And Commissioning Instructions

Share
Download
MR OILTAP R Installation And Commissioning Instructions Download Page 163

6 Commissioning the on-load tap-changer at the transformer manufacturer's site

Maschinenfabrik Reinhausen GmbH 2015

163

4427410/00 EN

OILTAP® R

Commissioning the on-load tap-changer at the
transformer manufacturer's site

Perform the following work and functional checks before commissioning the
transformer.

Bleeding on-load tap-changer head and suction pipe

Before first commissioning, the on-load tap-changer head and the suction
pipe on pipe connection S must be bled.

Bleeding on-load tap-changer head

1.

Open all forward and return valves in the pipe system.

2.

Remove screw cap on air-vent valve E1 on the on-load tap-changer
head cover.

Figure 210: Screw cap

3.

Use screwdriver to lift valve tappet on air-vent valve E1 and bleed on-
load tap-changer head.

Figure 211: Valve tappet

4.

Seal air-vent valve E1 with screw cap (tightening torque 10 Nm).

6

6.1

6.1.1

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands