manualshive.com logo in svg

MR OILTAP R, Installation And Commissioning Instructions

Share
Download
MR OILTAP R Installation And Commissioning Instructions Download Page 148

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

148

4427410/00 EN

OILTAP® R

12. Attach protective tube (inner tube) with a hose clip to the bearing collar

of the drive 

. Then slider upper protective tube (outer tube) over

adapter on bevel gear 

. Secure upper protective tube with hose clip

both at top end and at transition to bottom protective tube 

.

Figure 187: Mounting protective tube

 

Fitting drive shaft with cardan joints

NOTICE

 

Damage to drive shaft!

Damage to expansion bellows from bending cardan joint!
► Ensure a matching position of the opposing cardan joint straps!

Installation of the drive shaft with cardan joints is mainly designed as a verti-
cal drive shaft between motor-drive unit and bevel gear. Technically, a hori-
zontal design is also possible. Note, however, that when using the horizontal
design the guard plate supplied has to be adapted accordingly.

5.5.6.3

 

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands