manualshive.com logo in svg

MR OILTAP R, Installation And Commissioning Instructions

Share
Download
MR OILTAP R Installation And Commissioning Instructions Download Page 103

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

103

4427410/00 EN

OILTAP® R

Moving on-load tap-changer to adjustment position

► Move on-load tap-changer to adjustment position.

Figure 118: Adjustment position

Removing on-load tap-changer head cover

 WARNING

Danger of death or severe injury!

Danger of death or severe injury from explosive gases under the on-load
tap-changer head cover!
► Ensure that there are no naked flames, hot surfaces or sparks (for ex-

ample caused by static charging) in the immediate surroundings and
that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory

control, pressure relief device, pressure-operated relays) before remov-
ing the on-load tap-changer head cover.

► Do not operate any electric devices during the work (for example risk of

sparks caused by impact wrench).

► Only use conductive and grounded hoses, pipes and pump equipment

that are approved for flammable liquids.

NOTICE

 

Damage to the on-load tap-changer and transformer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer and transformer!
► Take care to avoid parts falling into the oil compartment.
► Check that you have the same number of small parts when disassem-

bling and reassembling.

5.3.8.2.1.1

5.3.8.2.1.2

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands