MR OILTAP R Installation And Commissioning Instructions Download Page 164

Page: 164 / 206

6 Commissioning the on-load tap-changer at the transformer manufacturer's site

Maschinenfabrik Reinhausen GmbH 2015

164

4427410/00 EN

OILTAP® R

Bleeding suction pipe on pipe connection S

Remove screw cap from pipe connection S.

Figure 212: Screw cap

NOTICE!

Open vent screw and bleed suction pipe. Make sure the suc-

tion pipe is fully vented. The insulation capability of the on-load tap-
changer to ground will otherwise be significantly impaired.

Close vent screw.

Seal vent screw with screw cap.

Grounding the on-load tap-changer

Connect the grounding screw on the on-load tap-changer head to the
transformer cover.

Figure 213: Grounding screw head

6.1.2

6.2

Summary of Contents for OILTAP R















































































































































































































Search results

Summary of Contents for OILTAP R

Reviews:

MR OILTAP R, Installation And Commissioning Instructions, Page: 164 / 206

Search results

Summary of Contents for OILTAP R

Reviews: