manualshive.com logo in svg

MR OILTAP R, Installation And Commissioning Instructions, Page: 165 / 206

Share
Download
MR OILTAP R Installation And Commissioning Instructions Download Page 165

6 Commissioning the on-load tap-changer at the transformer manufacturer's site

Maschinenfabrik Reinhausen GmbH 2015

165

4427410/00 EN

OILTAP® R

2.

Connect the grounding screw of the motor-drive protective housing to
the transformer tank.

Figure 214: Grounding screw on motor-drive unit

3.

When using a temperature sensor, ground the temperature sensor
housing on the on-load tap-changer using the grounding cable.

Performing tests on motor-drive unit

Function tests

► Perform function checks as described in relevant MR operating instruc-

tions "TAPMOTION® ED".

Dielectric tests on transformer wiring

► Note information relating to dielectric tests on transformer wiring in the

associated MR operating instructions "TAPMOTION® ED".

Performing trial tap-change operations

Before energizing the transformer, test tap change operations must be car-
ried out to check the mechanical functions of on-load tap-changer and mo-
tor-drive unit.

NOTICE

 

Damage to the on-load tap-changer!

Damage to the on-load tap-changer by actuating the on-load tap-changer
without oil!
► Before actuating the on-load tap-changer for the first time, the tap se-

lector must be completely immersed in transformer oil and the oil com-
partment completely filled with oil.

► The on-load tap-changer can be operated in the temperature range of

the surrounding transformer oil of between -25 ° and +105 °C and with
overload up to +115 °C in accordance with IEC 60214-1.

6.3

6.4

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments