MR ECOTAP VPD 3 30D-24 Page 83 Operating Instructions Manual Download

Page: 83 / 132

7 Operation

Maschinenfabrik Reinhausen GmbH 2021

8209941/00 EN

ECOTAP

VPD

III 30D-24 / MD&C

To activate or deactivate the "Target position for loss of voltage" function,
proceed as follows:

The AVR MANUAL operating mode is active.

1. Press

until the desired parameter is displayed.

2. Press

to confirm the selection.

3. Press

until the desired parameter is displayed.

4. Press

to confirm the selection.

5. Press

to set the desired option.

6. Press

to confirm the selection.

7. Press

until code 3 is displayed.

8. Press

to confirm the selection.

9. Press

to save the setting.

7.4.5 Number of operating positions (P7)

The control unit can be configured for different types of ECOTAP® VPD®
on-load tap-changer. You must set the number of operating positions ac-
cordingly.

When you perform the automatic adjustment (F1.1), the parameter P7 is au-
tomatically set to the correct value.

To set the number of operating positions, proceed as follows:

The AVR MANUAL operating mode is active.

1. Press

until the desired parameter is displayed.

2. Press

to confirm the selection.

3. Press

to select the desired value.

4. Press

to confirm the selection.

Summary of Contents for ECOTAP VPD 3 30D-24





































































































































Search results

Summary of Contents for ECOTAP VPD 3 30D-24

Reviews:

Related manuals for ECOTAP VPD 3 30D-24

Brands by name

Popular brands

MR ECOTAP VPD 3 30D-24, Operating Instructions Manual

Search results

Summary of Contents for ECOTAP VPD 3 30D-24

Reviews:

Related manuals for ECOTAP VPD 3 30D-24

Brands by name

Popular brands