MR ECOTAP VPD 3 30D-24 Page 60 Operating Instructions Manual Download | Manualshive

Page: 60 / 132

background image

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2021

60

8209941/00 EN

ECOTAP

®

VPD

®

III 30D-24 / MD&C

Figure 38: Example: Shield with cable screw connections

6.3.3.3 Requirements for the power supply circuit

Power supply during commissioning tests

DANGER

Danger of explosion!

An incorrect position of the on-load tap-changer or the motor drive shaft can
lead to malfunction and, consequently, to an overload of the on-load tap-
changer. This overload can lead to an explosion in the transformer.

► Carry out automatic adjustment and trial tap-change operations on a volt-

age-free transformer.

► Supply the controller and motor-drive unit via a separate voltage source

during these tests.

► If a separate voltage source is not available, it is imperative that the cor-

rect position of the on-load tap-changer and motor-drive unit be checked
again according to the section "Mounting the motor drive" before these
tests.

Ensure the correct position of motor-drive unit: The feather key

of the mo-

tor shaft must be facing the mark

:

Figure 39:

Check the position of the motor-drive unit

«
...
58
59
60
61
62
...
»

Summary of Contents for ECOTAP VPD 3 30D-24





































































































































Reviews:

No comments

Related manuals for ECOTAP VPD 3 30D-24

Brand: THORLABS Pages: 44

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: XAG Pages: 24

Brand: Tascam Pages: 8

Brand: B-K lighting Pages: 5

Brand: B-K lighting Pages: 4

Brand: B-K lighting Pages: 3

Brand: BACtrack Pages: 16

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: Jacobsen Pages: 20

Brand: MacDon Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands