manualshive.com logo in svg

MR ECOTAP VPD 3 30D-24, Operating Instructions Manual, Page: 34 / 132

Share
Download
MR ECOTAP VPD 3 30D-24 Operating Instructions Manual Download Page 34

5 Mounting

Maschinenfabrik Reinhausen GmbH 2021

34

8209941/00 EN

ECOTAP

®

 VPD

®

 III 30D-24 / MD&C

4. Also check the position of the shaft of the on-load tap-changer: If the pre-

vious on-load tap-change operation has been finished correctly, the arrow
on the cam disk 

 will point to the arrow in the cover 

.

Figure 11: Position of the shaft of the on-load tap-changer

ð

If the shaft of the on-load tap-changer is in this position, the on-load
tap-changer is in a defined operating position. If this is not the case,
correct the position as described below.

5.

NOTICE!

 Only use the emergency drive shaft built into the sealing mod-

ule. Failure to do so can result in damage to the on-load tap-changer.

6. Pull the emergency drive shaft out of the bracket in the sealing module.

Figure 12: Removing emergency drive shaft

Summary of Contents for ECOTAP VPD 3 30D-24





































































































































Reviews:

No comments