Open a WC3 compliant web browser such as Microsoft Internet Explorer, Firefox, or Opera
to http://[ipaddress]/ or http://[name]/. The instrument information screen will be displayed
as shown in figure B.1. This figure provides the basic information about the configuration
and allows the user to enable or disable the LXI Identification. Click Enable Identify or
Disable Identify to change the state of the LXI Identification. When LXI Identification is
enabled, the LAN LED on the back of the power supply unit will blink. This can help the
user to quickly locate the power supply and distinguish it from similar devices.
To change the Ethernet interface's network settings, click the Configure tab in the upper
right. The browser will prompt for a username and password if you have not authenticated
the device already. To authenticate, enter admin for the username and leave the password
field blank. The instrument configuration screen, figure B.2, will appear. This page enables
the user to change the Hostname (which corresponds to the NetBIOS name), the description,
password, and TCP/IP configuration. After changes to the configuration are made, click the
Save Config button. The configuration will be saved, the Ethernet interface will reboot and
instructions, shown in figure B.3, will be displayed for reconnecting to the interface.
Web control of the power supply requires Adobe Flash Player which is available for
download from http://get.adobe.com/flashplayer/. To control the power supply, click the
Control tab in the upper right. The browser may prompt for a username and password if you
have not authenticated the device already. To authenticate, enter admin for the username
and leave the password field blank. The power supply’s control panel, figure B.4, will be
displayed. The screen displays the same status information as the front panel of the power
supply and allows the user to control and read voltage, current, over voltage trip, over
current trip, mode of operation, and diagnostics. Like the front panel, a diagnostic condition
can be cleared using the clear button. Only one user can control the power supply at a time
with the Remote Interface Software
or the web interface.
125
Summary of Contents for DP SERIES II
