Moxa Technologies AirWorks AWK-5222 User Manual Download

Page: 4 / 100

Relay Status ................................................................................................................ 3-51

DI and Power Status ................................................................................................... 3-51

Maintenance........................................................................................................................... 3-52

Console Settings ......................................................................................................... 3-52

Ping............................................................................................................................. 3-52

Firmware Upgrade...................................................................................................... 3-53

Config Import Export ................................................................................................. 3-53

Load Factory Default.................................................................................................. 3-54

Password..................................................................................................................... 3-54

Misc. Settings ............................................................................................................. 3-54

Save Configuration ................................................................................................................ 3-55

Restart .................................................................................................................................... 3-55

Logout.................................................................................................................................... 3-56

Chapter 4

Software Installation/Configuration ...........................................................4-1

Overview.................................................................................................................................. 4-2

AWK Search Utility ................................................................................................................. 4-2

Installing AWK Search Utility ..................................................................................... 4-2

Configuring AWK Search Utility ................................................................................. 4-5

Chapter 5

Other Console Configurations ....................................................................5-1

RS-232 Console Configuration (115200, None, 8, 1, VT100)................................................. 5-2

Configuration by Telnet and SSH Consoles............................................................................. 5-4

Configuration by Web Browser with HTTPS/SSL .................................................................. 5-5

Disabling Telnet and Browser Access...................................................................................... 5-6

Chapter 6

References....................................................................................................6-1

Beacon ..................................................................................................................................... 6-2

DTIM ....................................................................................................................................... 6-2

Fragment .................................................................................................................................. 6-2

RTS Threshold ......................................................................................................................... 6-2

STP and RSTP ......................................................................................................................... 6-2

The STP/RSTP Concept ............................................................................................... 6-2

Differences between RSTP and STP ............................................................................ 6-3

Chapter 7

Supporting Information ...............................................................................7-1

About This User’s Manual ....................................................................................................... 7-2

DoC (Declaration of Conformity)............................................................................................ 7-3

Federal Communication Commission Interference Statement ..................................... 7-3

R&TTE Compliance Statement .................................................................................... 7-4

Firmware Recovery.................................................................................................................. 7-4

Technical Support Contact Information ................................................................................... 7-6

Summary of Contents for AirWorks AWK-5222




































































































Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-5222, User Manual

Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands