Moxa Technologies AirWorks AWK-5222 User Manual Download | Manualshive

Page: 56 / 100

background image

AWK-5222 User’s Manual

Other Console Configurations

3-38

SNMP Agent

The AWK-5222 supports SNMP V1/V2c/V3. SNMP V1 and SNMP V2c use a community string
match for authentication, which means that SNMP servers access all objects with read-only or
read/write permissions using the community string

public

/

private

(default value). SNMP V3,

which requires you to select an authentication level of MD5 or SHA, is the most secure protocol.
You can also enable data encryption to enhance data security.

The AWK-5222’s MIB can be found in the software CD and supports reading the attributes via
SNMP. (Only

get

method is supported.)

SNMP security modes and security levels supported by the AWK-5222 are shown in the following
table. Select the security mode and level that will be used to communicate between the SNMP
agent and manager.

Protocol
Version

Setting on
UI web
page

Authentication
Type

Data
Encryption

Method

V1, V2c Read
Community

Community

string No

Use a community string match for
authentication

SNMP
V1, V2c

V1, V2c
Write/Read
Community

Community

string No

Use a community string match

for

authentication

No-Auth No

No

Use account with admin or user to
access objects

MD5 or SHA

Authentication
based on MD5

or

SHA

No

Provides authentication based on
HMAC-MD5, or HMAC-SHA
algorithms. 8-character passwords are
the minimum requirement for
authentication.

SNMP V3

MD5 or SHA

Authentication
based on MD5

or

SHA

Data
encryption

key

Provides authentication based on
HMAC-MD5 or HMAC-SHA
algorithms, and data encryption key.
8-character passwords and a data
encryption key are the minimum
requirements for authentication and
encryption.

«
...
54
55
56
57
58
...
»

Summary of Contents for AirWorks AWK-5222





































































































Reviews:

No comments

Related manuals for AirWorks AWK-5222

Brand: Paradyne Pages: 11

Brand: Paradyne Pages: 19

Brand: Paradyne Pages: 32

COMSPHERE 3550 Series

Brand: Paradyne Pages: 153

Jetstream CPX-1000

Brand: Paradyne Pages: 141

FrameSaver 9783

Brand: Paradyne Pages: 28

COMSPHERE 6800 Series

Brand: Paradyne Pages: 7

Brand: SAF Pages: 30

Brand: Amperes Pages: 8

Brand: Planet Pages: 20

Brand: ZyXEL Communications Pages: 2

Brand: Dahua Pages: 24

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

Brand: NA Pages: 22

Brand: 3Com Pages: 50

Brand: B&B Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands