Moxa Technologies AirWorks AWK-5222 User Manual Download | Manualshive

Page: 37 / 100

background image

AWK-5222 User’s Manual

Other Console Configurations

3-19

WEP key 1-4

Setting

Description

Factory Default

ASCII type:
64 bits: 5 chars
128 bits: 13chars
HEX type:
64 bits: 10 hex chars
128 bits: 26 hex chars

A string that can be used as a WEP
seed for RC4 encryption engine.

None

WPA/WPA2-Personal

WPA (Wi-Fi Protected Access) and WPA2 are significantly improved encryption methods of WEP.
WPA is a security standard based on 802.11i draft 3, while WPA2 is based on the fully ratified
version of 802.11i. The initial vector is transmitted, encrypted, and enhanced with its 48 bits, twice
as long as WEP. The key is regularly changed so that true session is secured.

Even though AES encryption is only included in the WPA2 standard, it is widely available in the
WPA security mode of some wireless APs and clients as well. The AWK-5222 also supports AES
algorithms in WPA and WPA2 for better compatibility.

Personal versions of WPA/WPA2, also know as WPA/WPA-PSK (

Pre-Shared Key

), provides a

simple way of encrypting a wireless connection for high confidentiality. A

Passphrase

is used as a

basis for encryption methods (or cipher types) in a WLAN connection. The passphrases should be
complex and as long as possible. The number of ASCII characters of the Passphrase must be at
least 8 and can go up to 63. For security reason, this passphrase should be disclosed to the relevant
users only and changed regularly.

WPA Type

Setting

Description

Factory Default

Personal Provides

Pre-Shared

Key-enabled

WPA and WPA2

Enterprise

Provides enterprise-level security
for WPA and WPA2

Personal

Encryption method

Setting

Description

Factory Default

TKIP

T

emporal

K

ey

I

ntegrity

P

rotocol is

enabled

AES

A

dvance

E

ncryption

S

ystem is

enabled

Mixed

*

Provides TKIP broadcast key and
TKIP+AES unicast key for some

TKIP

«
...
35
36
37
38
39
...
»

Summary of Contents for AirWorks AWK-5222





































































































Reviews:

No comments

Related manuals for AirWorks AWK-5222

Brand: PaloAlto Networks Pages: 3

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Brand: D-Link Pages: 31

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

Brand: Gemtek Systems Pages: 51

Brand: RubyTech Pages: 25

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: Ubiquiti Pages: 23

Comet 3356P-LAN

Brand: ZyXEL Communications Pages: 38

Brand: Zhone Pages: 28

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Brand: Vivotek Pages: 317

Brand: Patton electronics Pages: 8

ClareVision CV-M161620-04

Brand: Clare Controls Pages: 32

BNI EIP-508 05-Z015 Series

Brand: Balluff Pages: 74

Westermo Ibex-RT-330-5G Series

Brand: IBEX Pages: 36

Brand: TP-Link Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands