Moxa Technologies AirWorks AWK-5222 User Manual Download

Page: 25 / 100

AWK-5222 User’s Manual

Other Console Configurations

3-7

Setting

Description

Factory Default

User adjustable time

The date and time parameters allow
configuration of the local time with
immediate activation.

None
(yyyy/mm/dd hh:mm:ss
format; 24-hour format.)

Time zone

Setting

Description

Factory Default

User selectable time
zone

The time zone setting allows
conversion from GMT (Greenwich
Mean Time) to local time.

GMT (Greenwich Mean
Time)

ATTENTION

Changing the time zone will automatically adjust the

Current local time

. You should configure

the

Time zone

before setting the

Current local time

Daylight saving time

Setting

Description

Factory Default

Enable/ Disable

Daylight saving time (also know as
DST or summer time) involves
advancing clocks (usually 1 hour)
during the summer time to provide an
extra hour of daylight in the
afternoon.

Disable

When

Daylight saving time

is enabled, the following parameters can be shown:

The

Starts at

parameter allows users to enter the date that daylight saving time begins.

The

Stops at

parameter allows users to enter the date that daylight saving time ends.

The

Time offset parameter

indicates how many hours forward the clock should be advanced.

Time server 1/ 2

Setting

Description

Factory Default

The 1st/ 2nd time server
IP/Name

IP or Domain address of NTP time
server. The 2nd time will be used if
the 1st NTP server fails to connect.

None

Query period

Setting

Description

Factory Default

Query period time
(1- 9999 seconds)

This parameter determines how often
the time is updated from the NTP
server.

600 (seconds)

Summary of Contents for AirWorks AWK-5222




































































































Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-5222, User Manual

Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands