Moxa Technologies AirWorks AWK-5222 User Manual Download

Page: 39 / 100

AWK-5222 User’s Manual

Other Console Configurations

3-21

WPA Type

Setting

Description

Factory Default

Personal Provides

Pre-Shared

Key-enabled

WPA and WPA2

Enterprise

Provides enterprise-level security
for WPA and WPA2

Personal

Encryption method

Setting

Description

Factory Default

TKIP

emporal

ntegrity

rotocol is

enabled

AES

dvance

ncryption

ystem is

enabled

Mixed

Provides TKIP broadcast key and
TKIP+AES unicast key for some
legacy AP clients. This option is
rarely used.

*This option is

available in Redundant AP, AP, or
Master mode only, and cannot
support AES-enabled clients.

TKIP

Primary/ Secondary RADIUS server IP

Setting

Description

Factory Default

The IP address of
RADIUS server

Specifies the delegated RADIUS
server for EAP

None

Primary/ Secondary RADIUS port

Setting

Description

Factory Default

Port number

Specifies the port number of the
delegated RADIUS server

1812

Summary of Contents for AirWorks AWK-5222




































































































Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-5222, User Manual

Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands