Moxa Technologies AirWorks AWK-5222 User Manual Download | Manualshive

Page: 9 / 100

background image

AWK-5222 User’s Manual

Introduction

1-5

ATTENTION

The AWK-5222 is NOT a portable mobile device and should be located at least 20cm away from
the human body. The AWK-5222 is NOT designed for the general public. To deploy AWK-5222s
and establish a wireless network safely, a well-trained technician is required for installation.

Functional Design

LED Indicators

The LEDs on the front panel of AWK-5222 allow you to identity the status and wireless settings
quickly.

LED Color State

Description

Front Panel LED Indicators (System)

On

Power is being supplied from power input 1.

PWR1

Green

Off

Power is

not

being supplied from power input

1.

On

Power is being supplied from power input 2.

PWR2

Green

Off

Power is

not

being supplied from power input

2.

On

Power is being supplied via PoE.

PoE

Amber

Off Power

is

not

being supplied via PoE.

Blinking

Cannot get an IP address from the DHCP
server (interval: 1 sec)

FAULT

Red

Off

There is no error condition.

Green Software

Ready

Blinking Green

The AWK has been located by AWK Search
Utility(interval: 1 sec)

STATE

Green/Red

Red

Booting or Error condition

Green On

WLAN1 functions in

Client

mode.

Blinking Green

WLAN1’s data communication is running in

Client

mode

Amber On

WLAN1 functions in

AP/Bridge

mode.

Blinking

Amber

WLAN1’s data communication is running in

AP/Bridge

mode

WLAN1

Green/Amber

Off

WLAN1 is not in use.

Green On

WLAN2 function is in

Client

mode.

Blinking Green

WLAN2’s data communication is running in

Client

mode

Amber On

WLAN2 function is in

AP/Bridge

mode.

Blinking

Amber

WLAN2’s data communication is running in

AP/Bridge

mode

WLAN2

Green/Amber

Off

WLAN2 is not in use.

TP Port (LAN1, LAN2) LED Indicators (Port Interface)

On

TP port’s 10 Mbps link is

active

.

Blinking

Data is being transmitted at 10 Mbps

10M

Yellow

Off

TP port’s 10 Mbps link is

inactive

.

On

TP port’s 100 Mbps link is

active

.

Blinking

Data is being transmitted at 100 Mbps

100M

Green

Off

TP port’s 100 Mbps link is

inactive

.

«
...
7
8
9
10
11
...
»

Summary of Contents for AirWorks AWK-5222





































































































Reviews:

No comments

Related manuals for AirWorks AWK-5222

Brand: JCG Pages: 2

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

Brand: A10 Pages: 52

Brand: STONEFLY Pages: 48

Brand: process-informatik Pages: 8

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Brand: Eneo Pages: 68

Brand: ADTRAN Pages: 2

Brand: Rajant Corporation Pages: 40

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: Airlinkplus Pages: 20

Brand: PairGain Pages: 80

Brand: C&H Technologies Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands