Moxa Technologies AirWorks AWK-5222 User Manual Download

Page: 71 / 100

AWK-5222 User’s Manual

Other Console Configurations

3-53

Firmware Upgrade

The AWK-5222 can be enhanced with more value-added functions by installing firmware

upgrades. The latest firmware is available at Moxa’s download center.

Before running a firmware upgrade, make sure the AWK-5222 is off-line. Click the

Browse

button to specify the firmware image file and click

Firmware Upgrade and Restart

to start the

firmware upgrade. After the progress bar reaches 100%, the AWK-5222 will reboot itself.

When upgrading your firmware, the AWK-5222’s other functions are forbidden.

ATTENTION

Please make sure the power source is stable when you upgrade your firmware. An unexpected
power breakup may damage your AWK-5222.

Config Import Export

You can back up or restore the AWK-5222’s configuration with

Config Import Export

In the

Config Import

section, click

Browse

to specify the configuration file and click

Config

Import

button to begin importing the configuration.

In the

Config Export

section, click the

Config Export

button and save the configuration file onto

your local storage media. The configuration file is a text file and you can view and edit it with a
general text-editing tool.

Summary of Contents for AirWorks AWK-5222




































































































Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-5222, User Manual

Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands