Moxa Technologies AirWorks AWK-5222 User Manual Download | Manualshive

Page: 10 / 100

background image

AWK-5222 User’s Manual

Introduction

1-6

ATTENTION

When the LEDs for

STATE

(Green),

FAULT

,

WLAN1

and

WLAN2

all light up simultaneously

and blink at one-second intervals, it means the system failed to boot. This may be due to improper
operation or uncontrollable issues, such as an unexpected shutdown during firmware update. To
recover the firmware, refer to “Firmware Recovery” in Chapter 6.

Beeper

The beeper signals that the system is ready with two short beeps.

Reset Button

The

RESET

button is located on the top panel of the AWK-5222. You can reboot the AWK-5222

or reset it to factory default settings by pressing the

RESET

button with a pointed object such as

an unfolded paper clip.

y

System reboot:

Hold the RESET button down for

under

5 seconds and then release.

y

Reset to factory default:

Hold the RESET button down for

over

5 seconds until the

STATE

LED starts blinking green. Release the button to reset the AWK-5222.

AUX1

AUX2

RESET button

«
...
8
9
10
11
12
...
»

Summary of Contents for AirWorks AWK-5222





































































































Reviews:

No comments

Related manuals for AirWorks AWK-5222

Brand: D-Link Pages: 10

Brand: Paradyne Pages: 22

Brand: Panasonic Pages: 44

Brand: Telex Communications Pages: 28

Brand: axing Pages: 4

Brand: Connectland Pages: 10

Brand: Extron electronics Pages: 19

Brand: Extreme Networks Pages: 51

Brand: Socket Pages: 18

Brand: Juniper Pages: 230

Brand: NETGEAR Pages: 2

Westermo Ibex-RT-330-5G Series

Brand: IBEX Pages: 36

ICPE2600 Series

Brand: 3onedata Pages: 5

Brand: Juniper Pages: 12

Thin Twinax Terminal LM-6488

Brand: Ringdale Pages: 15

C52iG-5HaxD2HaxD-TC

Brand: MikroTik Pages: 23

CCR2004-16G-2S+PC

Brand: MikroTik Pages: 20

Brand: Westermo Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands