Moxa Technologies AirWorks AWK-5222 User Manual Download

Page: 66 / 100

AWK-5222 User’s Manual

Other Console Configurations

3-48

SNMP Trap Receiver Settings

SNMP traps are defined in SMIv1 MIBs (SNMPv1) and SMIv2 MIBs (SNMPv2c). The two styles
are basically equivalent, and it is possible to convert between the two. You can set the parameters
for SNMP trap receivers through the web page.

1st / 2nd Trap version

Setting

Description

Factory Default

SNMP trap defined in SNMPv1

SNMP trap defined in SNMPv2

1st / 2nd Trap server IP/name

Setting

Description

Factory Default

IP address or host name Enter the IP address or name of the

trap server used by your network.

None

1st / 2nd Trap community

Setting

Description

Factory Default

Max. 31 characters

Use a community string match with a
maximum of 31 characters for
authentication.

alert

Summary of Contents for AirWorks AWK-5222




































































































Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-5222, User Manual

Search results

Summary of Contents for AirWorks AWK-5222

Reviews:

Related manuals for AirWorks AWK-5222

Brands by name

Popular brands