Moxa Technologies AirWorks AWK-3121 User Manual Download Page 52

Page: 52 / 90

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-36

System-related events

Event is triggered when…

System restart (warm start)

The AWK-3121 is rebooted, such as when its settings
are changed (IP address, subnet mask, etc.).

Network-related events

Event is triggered when…

LAN link on

The LAN port is connected to a device or network.

LAN link off

The port is disconnected (e.g., the cable is pulled out,
or the opposing device shuts down).

Client joined/ left

(for AP mode)

A wireless client is associated or disassociated.

WLAN connected to AP

(for Client mode)

The AWK-3121 is associated with an AP.

WLAN disconnected

(for Client mode)

The AWK-3121 is disassociated from an AP.

Config-related events

Event is triggered when…

Configuration Changed

A configuration item has been changed.

Configuration file import via Web
Console

The configuration file is imported to the AWK-3121.

Console authentication failure

An incorrect password is entered.

Firmware upgraded

The AWK-3121’s firmware is updated.

Power events

Event is triggered when…

Power 1/2 transition (On -> Off)

The AWK-3121 is powered down in PWR1/2.

PoE transition (On -> Off)

The AWK-3121 is powered down in PoE.

Power 1/2 transition (Off -> On)

The AWK-3121 is powered via PWR1/2.

PoE transition (Off -> On)

The AWK-3121 is powered via PoE.

DI events

Event is triggered when…

DI1/2 transition (On -> Off)

Digital Input 1/2 is triggered by on to off transition

DI1/2 transition (Off -> On)

Digital Input 1/2 is triggered by off to on transition

Summary of Contents for AirWorks AWK-3121


























































































Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-3121, User Manual

Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands