Moxa Technologies AirWorks AWK-3121 User Manual Download Page 40

Page: 40 / 90

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-24

NOTE

Make sure the same

Transmission distance

parameters are set in both

and

Client

sides, and

both

Bridges

. When this parameter is more than 500, an optimal algorithm will be enabled to

support long-distance transmission.

Transmission enhancement

is also recommended to enable communication at both ends when

long-distance transmission is required. A high-gain antenna installed at a fixed antenna
connector can also improve performance. (Select

Antenna

at MAIN or AUX.)

Antenna

Setting

Description

Factory Default

Auto

The AWK-3121 uses two antennas (MAIN and
AUX) and enables the diversity function for
reducing multipath effect.

MAIN

Diversity function is disabled. Only MAIN
antenna is in use.

AUX

Diversity function is disabled. Only AUX
antenna is in use.

Auto

EAPOL Version

Setting

Description

Factory Default

EAPOL version 1 was standardized in the 2001
version of 802.1X, which is much more
commonly implemented.

EAPOL version 2 was specified in
802.1X-2004.

Turbo Roaming

(for Client mode only)

Setting

Description

Factory Default

Enable/ Disable

Moxa’s Turbo Roaming can enable rapid
handover when the AWK-3121, as a client,
roams among a group of APs.

Disable

When Turbo Roaming is enabled, RF type and Scan channels will be shown as follows. RF type
shows the current

RF type

, which this client is using now. You can set up

Scan channels

for the

APs among which this client is going to roam. There are three Scan channels available. Please note
that the

Scan channels

may need to be modified when the

RF type

is changed. (For example,

channel 36 is not available in

B/G Mix

mode.)

Summary of Contents for AirWorks AWK-3121


























































































Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-3121, User Manual

Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands