Moxa Technologies AirWorks AWK-3121 User Manual Download Page 43

Page: 43 / 90

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-27

DHCP server (AP only)

Setting

Description

Factory Default

Enable

Enables AWK-3121 as a DHCP server

Disable

Disable DHCP server function

Disable

Default gateway

Setting

Description

Factory Default

IP address of a default
gateway

The IP address of the router that connects to
an outside network

None

Subnet mask

Setting

Description

Factory Default

subnet mask

Identifies the type of sub-network (e.g.,
255.255.0.0 for a Class B network, or
255.255.255.0 for a Class C network)

None

Primary/ Secondary DNS server

Setting

Description

Factory Default

IP address of Primary/
Secondary DNS server

The IP address of the DNS Server used by
your network. After entering the DNS
Server’s IP address, you can use URL as
well. The Secondary DNS server will be
used if the Primary DNS server fails to
connect.

None

Start IP address

Setting

Description

Factory Default

IP address

Indicates the IP address which AWK-3121
can start assigning

None

Maximum number of users

Setting

Description

Factory Default

1 – 999

Specifies how many IP address can be
assigned continuously

None

Client lease time

Setting

Description

Factory Default

1 – 10 days

The lease time for which an IP address is
assigned. The IP address may go expired
after the lease time is reached.

10 (days)

Summary of Contents for AirWorks AWK-3121


























































































Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-3121, User Manual

Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands