Moxa Technologies AirWorks AWK-3121 User Manual Download Page 51 | Manualshive

Page: 51 / 90

background image

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-35

Admin auth type

(for V1, V2c, V3, and V3 only)

Setting

Description

Factory Default

No Auth

Use

admin

account to access objects. No

authentication

MD5

Provide authentication based on the HMAC-MD5
algorithms. 8-character passwords are the minimum
requirement for authentication.

SHA

Provides authentication based on
HMAC-SHA algorithms. 8-character passwords are
the minimum requirement for authentication.

No Auth

Admin private key

(for V1, V2c, V3, and V3 only)

Setting

Description

Factory Default

Disable

No data encryption

DES

DES-based data encryption

AES

AES-based data encryption

Disable

Private key

A data encryption key is the minimum requirement for data encryption (maximum of 63
characters)

Private MIB Information Device Object ID

Also know as

OID

. This is the AWK-3121’s enterprise value. It is fixed.

Auto Warning Settings

Since industrial-grade devices are often located at the endpoints of a system, these devices will
not always know what is happening elsewhere on the network. This means that these devices,
including wireless APs or clients, must provide system maintainers with real-time alarm
messages. Even when system administrators are out of the control room for an extended period,
they can still be informed of the status of devices almost instantaneously when exceptions
occur.

In addition to logging these events, the AWK-3121 supports different approaches to warn
engineers automatically, such as SNMP trap, e-mail, and relay output. It also supports two
digital inputs to integrate sensors into your system to automate alarms by email and relay
output.

System Log

System Log Event Types

Detail information for grouped events is shown in the following table. You can check the box for

Enable log

to enable the grouped events. All default values are enabled (checked). The log for

system events can be seen in

Status

Æ

System Log

.

«
...
49
50
51
52
53
...
»

Summary of Contents for AirWorks AWK-3121



























































































Reviews:

No comments

Related manuals for AirWorks AWK-3121

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: Sangoma Pages: 6

Brand: Industrex Pages: 51

Armor 101 Series

Brand: Lochinvar Pages: 28

Armor 101 Series

Brand: Lochinvar Pages: 44

RouterBOARD Groove

Brand: MikroTik Pages: 4

ICS-G7748A Series

Brand: Moxa Technologies Pages: 10

Brand: Zonet Pages: 2

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Brand: Watchguard Pages: 30

Brand: National Instruments Pages: 130

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: Hauppauge Pages: 55

Brand: Intel Pages: 958

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands