Moxa Technologies AirWorks AWK-3121 User Manual Download Page 8

Page: 8 / 90

AirWorks AWK-3121 User’s Manual

Introduction

1-4

Alarm Contact

1 relay output (capacity: 1A @24VDC)

Digital Input

2 electrically-isolated inputs

‧

+3 to -30V for state “0” (OFF)

‧

13 to 30V for state “1” (ON)

‧

Max. input current: 8 mA

Console

RS-232 (RJ45 type)

LAN Port

10/100BaseT(X) auto negotiation speed

LED Indicators

PWR1, PWR2, PoE, FAULT, STATE, Signal Strength,
CLIENT MODE, BRIDGE MODE, WLAN, 10M, 100M

Power

Input Voltage

12 to 48 VDC, redundant dual DC power inputs or
48 VDC Power-over-Ethernet (IEEE 802.3af)

Input Current

0.494 to 0.121 A (@ 12 to 48 VDC)

Input Current (@ 24VDC)

0.3 A

Overload Current Protection 1.6 A
Reverse Polarity Protection

Present

Mechanical

Dimensions

53.6 x 135 x 105 mm (2.11 x 5.31 x 4.13 in)

Weight 850

Installation

DIN-rail, or Wall Mounting (with optional wall mounting kit)

Casing

IP30 protection, aluminum case

Environment

Operating Temperature:

Standard models: 0 to 60°C (32 to 140°F)
Wide Temp Models: -40 to 75°C (-40 to 167°F)

Storage Temperature:

-40 to 85ºC (-40 to 185ºF)

Ambient Relative Humidity

5 to 95% (non-condensing)

Regulatory Approvals*

Safety: EN60950-1,

UL60950-1

Radio:

EN300 328, EN301 893, ARIB STD-33/T66/T71 (Japan)

EMC:

EN301 489-1/-17, FCC Part 15, EN55022/55024, IEC61000-6-2/-4

Environmental/EMC
compliancy

EN50155, EN50121-1/-4

* Please check Moxa

’

s website for the most up-to-date certification status.

Warranty

5 years

Details: See

http://www.moxa.com/warranty

ATTENTION

The AWK-3121 is NOT a portable mobile device and should be located at least 20 cm away from
the human body.

The AWK-3121 is NOT designed for the general public. To deploy AWK-3121 units and establish
a wireless network safely, a well-trained technician is required for installation.

Summary of Contents for AirWorks AWK-3121


























































































Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-3121, User Manual

Search results

Summary of Contents for AirWorks AWK-3121

Reviews:

Related manuals for AirWorks AWK-3121

Brands by name

Popular brands