Motorola Astro XTL 1500 User Manual Download

Page: 7 / 120

ALERT TONES

Type of Tone

Indication

Action

Short, low-
pitched tone

Unsuccessful power-up.
Radio failed self-test.
Radio not ready for use.

Contact your
service
representative.

Invalid (bad) key press.
A key press was
rejected.

Time-out timer warning.
Transmission time will
expire in four seconds.

Short,
medium-
pitched tone

Valid (good) key press.
A key press was
accepted.

Pressed emergency
button to enter
emergency. Emergency
entered.

Short, high-
pitched tone

Successful power-up.
Radio passed self-test.

Continuous,
low-pitched
tone

Transmit on receive-
only mode. Pressed
PTT button on receive-
only mode.

Release PTT
button.

Transmit inhibit on busy
mode. Pressed PTT
button while mode was
busy.

Invalid mode. An invalid
or unprogrammed
operation.

Time-out timer timed
out. Transmission was
terminated.

Release PTT
button.

Continuous,
medium-
pitched tone

Emergency alarm/call
exit. Exiting.

Faint beeping
tone every 10
seconds

Failsoft (trunked
systems only).

“Bah-bah-
bah-bah”

Phone busy. All modes
busy. Radio is in queue.

Waiting for
next
available line.

Trunked system busy
(trunked systems only).
Radio is in queue.

Waiting for
next
available
mode.

Single,
medium-
pitched tones
followed by
group of four
medium-
pitched tones

Your page has been
received by the target
radio.

Group of two
medium-
pitched tones

Private Conversation
call or conventional
selective call received.

Group of
three
medium-
pitched (di-di-
dit) tones

Call back (trunked
systems only). A
talkgroup is now
available.

Okay to
transmit in that
talkgroup.

Group of four
medium-
pitched tones
every five
seconds

Call Alert (page)
received.

ALERT TONES (Continued)

Type of Tone

Indication

Action

ALERT TONES (SECURE-EQUIPPED
RADIOS ONLY)

Type of Tone

Indication

Action

One beep
immediately
after PTT button
press

Indicates clear
transmission on
secure-equipped radio.

Six medium-
pitched tones

Keyfail. Encryption key
lost or erased.

Reload key.

Six medium-
pitched tones
(continuous)

Keyfail. Radio set in
secure position. PTT is
being pressed.

Set radio to
“clear,” or
select a clear
mode, or
reload key.

Six medium-
pitched tones
on radio power-
up

Encrypted operation
problem. Radio is set
to either clear or
secure.

Reload key.

Six medium-
pitched tones
every five to ten
seconds

Encrypted operation
problem. PTT button
not being pressed.

Set radio to
“clear,” or
select a clear
mode, or
reload key.

Consecutive,
medium-pitched
tones

Loss of encryption key
during secure
operation.

Reload key.

Summary of Contents for Astro XTL 1500

























































































































Search results

Summary of Contents for Astro XTL 1500

Reviews:

Related manuals for Astro XTL 1500

Brands by name

Popular brands

Motorola Astro XTL 1500, User Manual

Search results

Summary of Contents for Astro XTL 1500

Reviews:

Related manuals for Astro XTL 1500

Brands by name

Popular brands