Motorola Astro XTL 1500 User Manual Download | Manualshive

Page: 93 / 120

background image

ASTRO XTL 1500 Digital Mobile Radio with Control Head

77

Troubleshooting

Troubleshooting

The following are suggestions to assist you in troubleshooting
possible operating problems.

If your radio is locked up or the display shows

FL 01/90

, turn the

radio off and then back on. If this does not correct the condition, take
the radio to a qualified radio technician for service.

If radio operation is intermittent, check with other persons using the
system for similar problems before taking the radio in for service.
Similar problems indicate a system malfunction rather than a radio
failure.

If symptoms persist or, if your unit exhibits other problems, contact a
qualified radio technician.

The cables that connect to the rear of
the radio could have live voltage on
some of their pins. Do not remove or
reconnect these cables. Only a
qualified radio technician should
perform this task. Service performed
by unauthorized personnel may cause
the radio to transmit an emergency
alarm even if the unit is turned off.

CAUTION

!

«
...
91
92
93
94
95
...
»

Summary of Contents for Astro XTL 1500

























































































































Reviews:

No comments

Related manuals for Astro XTL 1500

Brand: B&G Pages: 129

Brand: E.F. Johnson Company Pages: 75

Brand: Sangean Pages: 71

Brand: Yaesu Pages: 43

Brand: Hytera Pages: 22

PERSONAL TWO-WAY RADIO

Brand: Zartek Pages: 10

Brand: Covalue Pages: 12

BTH-500-R Series

Brand: Nextav Pages: 8

Brand: Noxon Pages: 20

Brand: GCT Pages: 35

Brand: Vitek Pages: 6

Brand: Craig Pages: 7

cNODE Maxi 31 Ex d

Brand: Kongsberg Pages: 50

Brand: Vertex Standard Pages: 4

Brand: Asus Pages: 192

Brand: Makita Pages: 25

TurboDyne Series

Brand: Rover Pages: 38

Brand: Ambient Weather Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands