GB
26SC2
26CC3
32SC2
32CC3
38SC2
38CC3
38CC4
50SC2
50CC3
50CC4
MALFUNCTIONS
MATERIAL JAM IN THE MACHINE:
(Auto-reverse function)
If a jam is caused by feeding in too much material, the
machine reacts as follows:
- The cutting mechanism is blocked, then runs briefly
in reverse (material is released) and stops. The
motor is switched off.
- The control display
(6) lights up.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove released paper from the feed slot (12).
- Cutting mechanism now runs forwards automatically
and shreds the remaining paper in the cutting
mechanism.
- The control display
(6) goes out. The LED display
of the forwards button (3) is permanently lit.
- Continue shredding with lower quantity of paper.
Material jam in safety feed slot (13)
- Remove released material.
Take care when removing material as
sharp edges may cause injury!
- The remaining material is now automatically fed into
the cutting mechanism again and shredded.
- The control display
(6) goes out. The LED display
of the forwards button (3) is permanently lit.
- When the material has run through, continue
shredding with correct quantities.
- If necessary, operate the cutting mechanism manually
forwards and backwards alternately until the material
has completely run through and has been shredded.
Wait each time until the motor stops
before switching direction!
MOTOR PROTECTION:
If the motor is overloaded, it switches off. The control
display
(9) flashes. Switch the machine off with the
rocker switch (1).
After a cooling down period of approx. 25-40 minutes
(depending on the model and room temperature), you
can switch the machine on again.
CHECKLIST IN THE EVENT OF FAULTS:
If the machine does not work, check the following
points:
- is
the
mains plug connected to the mains?
- is
the
rocker switch (1) switched on?
- is the machine in “Sleep” mode?
See “AUTOMATIC ENERGY SAVING”.
- has
the
user interlock been activated?
See “OPERATION OF THE USER INTERLOCK”.
- is
the
receptacle pushed in?
- is
the
receptacle full?
Follow the instructions in “EMPTYING THE
RECEPTACLE”.
- is there a material jam in the machine?
Follow the instructions in “MATERIAL JAM IN THE
MACHINE”.
- Has the motor been overloaded?
See
“MOTOR
PROTECTION”.
If none of the above applies, please contact your
dealer.
MAINTENANCE / DISPOSING
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through the
feed slot, or switch the machine to reverse and wipe
both “eyes” of the photocell with a brush.
17
fi g. 5
fi g. 6
MAINTENANCE OF THE
CUTTING MECHANISM (CROSS-CUT):
Cross-cut cutting mechanisms must be oiled
after a certain operating time.
If the control display
(7) lights up, proceed
as follows:
Pull out receptacle (14), take oil receptacle (17) (Fig.
6) out of the holder in the lower cabinet and push
receptacle in again.
Spread some oil on a sheet of paper and then feed
it into the cutting mechanism through the paper feed
slot (12).
The paper is drawn in and the oil thus gets into the
cutting mechanism.
Carry out oil supply as follows:
- Pull out receptacle (14) until the control display
(8) lights up.
- The control displays
(7) and
(4) flash.
- Press backwards button (4) and keep pressed until
the control display
(7) goes out.
- Push receptacle in again.
The cutting mechanism now automatically begins
the cleaning cycle (forwards operation/backwards
operation) and then switches off. The machine is
ready again. To re-order the special oil, see “SPECIAL
ACCESSORIES”.
AUTOMATIC ENERGY-SAVING:
If the machine is not used for a while, it automatically
switches to the so-called “Sleep” mode after approx.
30 mins. The LED display
of the function button
(2) for “Ready” goes out. To switch on again, briefly
press the function button. If the user interlock is
switched on, it must be deactivated again when the
machine is switched on again (see “
OPERATING THE
MACHINE
”).
DISPOSING OF THE MACHINE:
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service
life. Do not dispose of any of the parts
included in the machine or its packaging with
household waste.
TECHNICAL DATA
Model
Cutting width
paper / CD,DVD
Cutting capacity
paper / CD,DVD
Working width
Power
Noise level
Intermittent operation
ON / OFF
Dimensions
W x D x H
Weight
intimus 26SC2
4 mm / 6 mm
13 sheets* / 1 piece
235 mm
0.44 kW
app. 55 dB(A)
10 / 45 min
380 x 330 x 550 mm
16 kg
intimus 26CC3
4x28 mm / 6 mm
9 sheets* / 1 piece
235 mm
0.44 kW
app. 55 dB(A)
10 / 45 min
380 x 330 x 550 mm
18 kg
intimus 32SC2
4 mm/ 6 mm
17 sheets* / 1 piece
235 mm
0.55 kW
app. 55 dB(A)
10 / 45 min
390 x 360 x 600 mm
19 kg
intimus 32CC3
4x28 mm / 6 mm
12 sheets* / 1 piece
235 mm
0.55 kW
app. 55 dB(A)
10 / 45 min
390 x 360 x 600 mm
21 kg
intimus 38SC2
4 mm / 6 mm
22 sheets* / 1 piece
245 mm
0.74 kW
app. 55 dB(A)
30 / 90 min
420 x 380 x 700 mm
29 kg
intimus 38CC3
4x28 mm / 6 mm
16 sheets* / 1 piece
245 mm
0.74 kW
app. 55 dB(A)
30 / 90 min
420 x 380 x 700 mm
30 kg
intimus 38CC4
1.9x15 mm / 6 mm
13 sheets* / 1 piece
245 mm
0.74 kW
app. 55 dB(A)
30 / 90 min
420 x 380 x 700 mm
30 kg
intimus 50SC2
4 mm / 6 mm
26 sheets* / 1 piece
260 mm
0.75 kW
app. 55 dB(A)
30 / 90 min
450 x 390 x 800 mm
33 kg
intimus 50CC3
4x28 mm / 6 mm
19 sheets* / 1 piece
260 mm
0.75 kW
app. 55 dB(A)
30 / 90 min
450 x 390 x 800 mm
33 kg
intimus 50CC4
1.9x15 mm / 6 mm
15 sheets* / 1 piece
260 mm
0.90 kW
app. 55 dB(A)
30 / 90 min
450 x 390 x 800 mm
35 kg
* based on A4-paper 70g/m² at 230V/50Hz – 10%
Model
Power supply data
supply voltage / frequency / current consumption
intimus 26SC2
220V-240V/50Hz, 2.0 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 26CC3
220V-240V/50Hz, 2.0 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 32SC2
220V-240V/50Hz, 2.5 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 32CC3
220V-240V/50Hz, 2.5 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 38SC2
220V-240V/50Hz, 3,0 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 38CC3
220V-240V/50Hz, 3,0 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 38CC4
220V-240V/50Hz, 3,0 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 50SC2
220V-240V/50Hz, 2,9 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 50CC3
220V-240V/50Hz, 2,9 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
intimus 50CC4
220V-240V/50Hz, 3,5 amps
120V/60Hz, ---- amps
100V/50/60Hz, ---- amps
SPECIAL ACCESSORIES
Description Order-No.
Plastic bag, 300x300x700x0.018 mm (26/32)
99925
Plastic bag, 440x330x950x0.05 mm (38/50)
99977
Lubricant, 110 ml bottle
88035
Note: For orders of special accessories and spare parts,
please contact your dealer.
7
http://www.monomachines.com/
http://www.monomachines.com/