GB
26SC2
26CC3
32SC2
32CC3
38SC2
38CC3
38CC4
50SC2
50CC3
50CC4
OPERATION
Models intimus 38 / intimus 50
In order to also ensure stability for
these larger machines, the four
support feet (16) (Fig. 4) on the base
of the housing must be turned out
towards the fl oor!
OPERATING THE MACHINE
:
Note: When the machine is delivered, the function
of the user interlock is switched off.
For information on activating the user interlock,
please refer to the description in “OPERATION
OF THE USER INTERLOCK”.
To switch the machine into „ready-to-operate“
continue depending on the actual programmed
mode as follows:
Mode “User interlock switched off”
- Switch machine on with rocker switch (1)
(position “1”).
- Briefly press function button (2).
- The LED display
of the function button (2)
lights up for “Ready”. The machine can be
loaded.
Mode “User interlock switched on”
Note: While switching on the machine subject to
the procedure described below, the user interlock
will be temporarily deactivated.
- Switch machine on with rocker switch (1)
(position “1”).
- Briefly press function button (2).
- The Control display “User interlock activated”
(10) lights up.
- Keep forwards button (3) and backwards button
(4) pressed simultaneously for approx. 2 secs.
- The LED display
of the function button (2)
flashes for “not ready”.
- Briefly press function button (2).
- The LED display
of the function button (2)
is now permanently lit for “Ready”. The control
display
(10) goes out.
The machine can be loaded.
Note: When the machine is switched on again
from the “Sleep” mode, the activated user
interlock must be deactivated again.
MATERIAL FEED:
Feed paper into the cutting mechanism through
the paper feed slot (12) (Fig. 3).
Feed data carriers (CD, DVD or credit card)
into the cutting mechanism individually into the
separate safety feed slot (13) (Fig. 3).
The machine automatically switches to forwards
running, draws the material in and automatically
switches off after shredding.
When shredding papers, do not shred
CD/DVD at the same time, and vice
versa!
3
9
10
11
4
6
7
8
2
Note: For shredding transparent films, the
machine must be manually switched to forwards
running (press and hold the forwards button (3)
for approx. 2 secs.).
By briefly pressing the function button (2) (Stop
function), the shredding process can be stopped
at any time. To continue, press and hold the
forwards button (3) for approx. 2 secs.
If the machine is not used for a period of approx.
30 mins., it automatically switches to “Sleep”
mode. If the user interlock is switched on, it
must be deactivated again when the machine
is switched on again (see “
OPERATING THE
MASCHINE
”).
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL
DATA section!
Should the machine become
overloaded, follow the instructions under
“MATERIAL JAM IN MACHINE” under
“MALFUNCTIONS”.
EMPTYING THE RECEPTACLE (fi g. 4):
A two compartment receptacle ensures that waste
is separated. It consists of a paper receptacle
(14) and a separate collection tray (15) for the
shredded CDs, DVDs and credit cards.
The fill level of the collection tray
(15) is not displayed by the control
display!
When shredding large quantities of
CDs/DVDs (approx. 25 per load), please
check the fill level of the collection
tray occasionally and empty the tray
separately as required.
If the receptacle for paper is full, the machine
switches off. The control display
(11) lights up.
Proceed as follows:
- Pull the receptacle (14) with the collection
tray (15) out of the lower housing. The control
display
(8) lights up and the control display
(11) goes out.
- Dispose of the contents of the containers
separately.
- Push the empty receptacle with the collection
tray back into the lower housing. The control
display
(8) goes out. If there is still material in
one of the feed slots, the control display
(6)
now lights up.
- Briefly press the forwards button (3). The
remaining material is shredded and the display
(6) goes out.
Note: The machine only runs when the receptacle
is fully pushed in!
DYNAMIC LOAD DISPLAY:
Models intimus 38 / intimus 50
To prevent a material jam and thus ensure a
continual, effective destruction of the data carriers,
the current load level of the motor is displayed
during the shredding process by a coloured,
diffuse light in the feed slot as follows:
Green light:
load < 50%
Yellow light:
load 50 - 75%
Red light:
load 75 - 100%
MANUAL “SLEEP” MODE:
By keeping the function button (2) pressed for
approx. 3 secs. in “Ready” mode, the machine
is manually switched to “Sleep” mode. When the
user interlock is switched on, the locking function
of the user interlock is simultaneously activated.
The machine cannot be started. In order to
deactivate the user interlock, please refer to
“
OPERATING THE MASCHINE
”.
OPERATION OF THE USER INTERLOCK:
Set programming mode:
To enter programming mode, the machine must
be switched to “Ready” (see “
OPERATING THE
MASCHINE
”).
Proceed as follows:
- Pull out receptacle (14) until the control display
(8) lights up.
- Press and hold forwards button (3) for approx.
4 secs. The integrated LED display flashes.
You are now in programming mode.
Note: If programming is not completed within the
programming time window of approx. 20 secs.,
the machine automatically returns to “Ready”
mode.
Programming sequence
to switch user interlock on:
- Set programming mode (see above).
- Press forwards button (3) and backwards button
(4) simultaneously and keep them pressed until
the control displays
(10),
(2) and
(4)
fl ash.
- Push receptacle in again.
Programming is complete. Programming mode is
switched off automatically. The control displays
(10),
(2) and (4) continue to fl ash for approx.
5 secs to indicate completion of programming.
Programming sequence
to switch user interlock off:
- Set programming mode (see above).
- Press forwards button (3) and backwards button
(4) simultaneously and keep them pressed until
the control displays
(10) and
(4) flash.
- Push receptacle in again.
Programming is complete. Programming mode is
switched off automatically. The control displays
(10) and
(4) continue to flash for approx. 5 secs
to indicate completion of programming.
15
14
16
fi g. 1
fi g. 4
6
http://www.monomachines.com/
http://www.monomachines.com/
