Mizuho MOT-VS700 Series Operator'S Manual Download Page 41

Page: 41 / 83

Operation

4.7 Trendelenburg

WARNING

When you operate the Trendelenburg operation with a patient on the operating table,

The patient may fall from the operating table.

CAUTION

When performing the head down operation, be careful

may get damaged.
When performing the head down operation, be careful

base. It may get damaged.

Head plate

fixing knob

Reverse Trendelenburg (Head up)

Press

The tabletop moves to the head up position.

Head up

Trendelenburg (Head down)

Press

The tabletop moves to the head down position.

Head down

NOTE

The maximum angle of
head up is 30 degrees from
the level position.
30°

30°

When Trendelenburg is
operated in the opposite
direction from the current
Trendelenburg position, it
will stop in the level position.
Once it stops, release the
switch and press it once
again; the tabletop will be
tilted to the maximum angle.

NOTE

The maximum angle of head
down is 40 degrees from the
level position.

40°

Summary of Contents for MOT-VS700 Series




















































































Search results

Summary of Contents for MOT-VS700 Series

Reviews:

Related manuals for MOT-VS700 Series

Brands by name

Popular brands

Mizuho MOT-VS700 Series, Operator'S Manual

Search results

Summary of Contents for MOT-VS700 Series

Reviews:

Related manuals for MOT-VS700 Series

Brands by name

Popular brands