Mizuho MOT-VS700 Series Operator'S Manual Download Page 35

Page: 35 / 83

Operation

NOTE

When the battery is used

Turning on the power

Press

of the control unit or the start switch on the right

of the touch panel when no power cable is conn

power connector or the power switch is turned off.

"BATTERY MODE" appears on the touch panel, and

appears on

the display of the control unit.

Start switch

Check the display of the control unit.

The battery needs to be charged if the battery level icon turns to

on the monitor screen.

- Battery level display

100% - 70

69% - 20%

19% - 1%

ected to the

You can also use the battery

indicator of the touch panel

to check the charging status.

When the battery indicator

lights up only red, battery

charging is necessary.

Summary of Contents for MOT-VS700 Series




















































































Search results

Summary of Contents for MOT-VS700 Series

Reviews:

Related manuals for MOT-VS700 Series

Brands by name

Popular brands

Mizuho MOT-VS700 Series, Operator'S Manual

Search results

Summary of Contents for MOT-VS700 Series

Reviews:

Related manuals for MOT-VS700 Series

Brands by name

Popular brands