Mizuho MOT-VS700 Series Operator'S Manual Download Page 59 | Manualshive

Page: 59 / 83

background image

55

4

Operation

4.20 Attaching/detaching the back plate

The back plate is detachable.

Detaching the back plate

WARNING

Make sure to check that the back plate is inserted
securely. If the back plate moves, the patient may
get injured.
The back plate weighs 8 kg (18 lbs). Pay special
attention when handling it. It may drop and cause
damage or injury.
Do not detach the back plate while the head plate is
inserted into it. If the back plate with the head plate
inserted is detached, the head plate may drop and
cause injury.

1.

Pull up the back plate attaching/removing levers placed on
the bottom of the back plate at the same time.

2.

While still pulling up the back plate attaching/removing

it straight.

Back plate attaching/

removing lever

«
...
57
58
59
60
61
...
»

Summary of Contents for MOT-VS700 Series




















































































Reviews:

No comments

Related manuals for MOT-VS700 Series

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: Garelick Pages: 4

Brand: Kellfri Pages: 12

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

Brand: Mangar International Pages: 8

Brand: Malvern Instruments Pages: 30

Brand: zarges Pages: 36

Brand: TEC Pages: 6

Brand: U Technology Pages: 6

Brand: XanLite Pages: 2

Brand: X-Rite Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands