Mizuho MOT-VS700 Series Operator'S Manual Download Page 54

Page: 54 / 83

Operation

4.17 Reverse mode

When a patient is placed in a reverse head-to-foot orientation, the reverse mode allows the operation with
reference to the patient head.

Activating the reverse mode

Press

and select the reverse mode (Reverse

Orientation).

Press

The reverse mode turns to ON and a green frame appears.

The direction of lateral tilt, Trendelenburg and slide turns the other way
around, and the icons of the back plate and the head plate switch their
places with each other.
The operation changes to that with the patient head placed on the leg
plate.

Normal mode

Reverse mode

WARNING

The head plate can be attached to the back plate
and the Single Leg Section (reverse mode) only.

Allowable load: 135kg (298lbs)

Summary of Contents for MOT-VS700 Series




















































































Search results

Summary of Contents for MOT-VS700 Series

Reviews:

Related manuals for MOT-VS700 Series

Brands by name

Popular brands

Mizuho MOT-VS700 Series, Operator'S Manual

Search results

Summary of Contents for MOT-VS700 Series

Reviews:

Related manuals for MOT-VS700 Series

Brands by name

Popular brands