Mizuho MOS-1302B Operator'S Manual Download Page 63

Page: 63 / 86

Using the

leg traction

device

Attach the traction device and traction shoe right/left to the extension arm right/

left, then adjust their positions.

Attach and adjust the traction devices and traction shoes for left and right legs.

Attachment

Loosen

Extension arm,

right/left

Traction device,

traction shoe, right/left

Tighten

Loosen the fixing handle on the end of the

extension arm right/left, insert the traction

device into the insertion hole (outside) on

the extension arm right/left, then fix the

traction device by tightening the fixing

handle.

NOTE

Make sure to hold the traction

shoe when operating a

handle (except for the traction

adjusting handle).

Adjustment

Tighten

Loosen

Tighten

Loosen

Tighten

Loosen

Adjust the direction of the

traction shoe.

Adjust the height of the

traction shoe.

Adjust the angle of the traction

shoe.

Adjust the traction amount.

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands