Mizuho MOS-1302B Operator'S Manual Download Page 46

Page: 46 / 86

Operation

Adjustment of leg plate

2. Give turns to the leg plate fixing handle.

1. Hold the edge of the leg plate.

Detachment

(Leg plate fixing handle)

3. Hold both ends of the leg plate and pull it up.

2. While holding the edge of the leg plate, turn the

leg plate fixing handle until it engages with the leg

plate clutch.

1. Hold the both ends of the leg plate and insert the

leg plate shaft into the leg plate clutch.

Attachment

(Leg plate fixing handle)

WARNING

- When removing the leg plate,

be sure to hold the front edge

of the leg plate before turning

the handle. Otherwise the

leg plate may drop down and

cause injury.

- Make sure to tighten the leg

plate flexing handle and fixing

handle securely. If the leg plate

moves, the patient may get

injured.

Leg plate

Leg plate fixing

handle

Leg plate

Leg plate fixing

handle

Leg plate clutch

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands