Mizuho MOS-1302B Operator'S Manual Download Page 57

Page: 57 / 86

Using the

leg traction

device

Set the back plate in a level position.

See "Return to level" (page 37).

Attach the inner thigh support with pad for traction in lateral posture, pads, and

lateral pad.

Inner thigh support

with pad for traction

in lateral posture

Extension arm, right/left

Pad (small)

Inner thigh

column (small)

Pad (large)

Lateral pad

Height adjusting

collars

Attach them to the insertion hole of the

extension arm right/left in the order as

indicated bellow.

Use the height adjusting collars according to

the patient’s body size.

Insert the inner

thigh support

with pad for

traction in

lateral posture

as indicated in

the illustration.

Left lateral posture

Right lateral posture

Match the direction of the lateral pad with the

patient’s orientation.

The direction of the lateral pad changes depending

on the insertion direction of the inner thigh support

with pad for traction in lateral posture.

Adjust the positioning of the extension arm right/left.

Tighten

Loosen

Tighten

Loosen

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands