Mizuho MOS-1302B Operator'S Manual Download Page 36

Page: 36 / 86

Operation

Trendelenburg

1. Press

and

simultaneously.

The

tabletop will move to the head up position.

Reverse Trendelenburg

(Head up)

Trendelenburg (Head down)

Head up

NOTE

- The maximum angle of

head up or head down is

25 degrees from the level

position.

- When the tabletop in a

Trendelenburg or reverse-

Trendelenburg position is tilted

to the opposite side, it will stop

in the level position. Once it

stops, release the switch and

press it again; the tabletop will

continue tilting.

25°

WARNING

Make sure the patient is

secured on the table, for

example with a patient safety

strap. Otherwise, the patient

may fall of the table.

1. Press

and

simultaneously.

The tabletop will move to the head down
position.

Head down

SEAT DOWN

SEAT UP

SEAT DOWN

SEAT UP

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands