Mizuho MOS-1302B Operator'S Manual Download Page 38

Page: 38 / 86

Operation

Change height of the tabletop

1. Press

and

simultaneously.

The tabletop will move up.

Move up the tabletop

1. Press

and

simultaneously

The tabletop will move down.

Move down the tabletop

Move up

NOTE

- The highest position of the

tabletop is 1140mm(44.88in)

from the floor surface to the

upper surface of the tabletop.

- The lowest position of the

tabletop is 670mm(26.38in)

from the floor surface to the

upper surface of the tabletop.

- The column line shows the

position used when the leg

traction device apparatus

is attached. For how to

attach the leg traction device

apparatus, see "Examples

of combination of various leg

traction device components"

(page 47).

Position to attach

the leg traction

device apparatus

1140mm

(44.88in)

670mm

(26.38in)

Move down

RESTRICTION

The tabletop cannot be lowered

to the lowest position when the

seat plate is flexed more than

50° downward. Operate the

seat plate so that its downward

flex angle will be 50° or less.

SEAT DOWN

SEAT UP

SEAT DOWN

SEAT UP

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands