Mizuho MOS-1302B Operator'S Manual Download Page 11

Page: 11 / 86

Before use

Patient's position during surgical operation

- Do not rest the patient on the head side and leg side with the orientations reversed. Doing so

may cause the leg plate to get damaged.

- Make sure to attach the provided mattresses securely. Improper attachment may cause a patient

to get injured.

- Position a patient's body at least 1

(0.39in)

away from the side rails. When using the electric

scalpel,

they may become hot and if the body touches the rails, it may cause the patient to get

burned.

Positioning the patient

Follow the steps below to position the patient.
1. Attach the accessory mattresses onto the tabletop.
2. Put the patient on the mattresses.
3. Position the patient according to the purpose of the surgical operation.

WARNING

Installation of the operating table

uneven floor surface

pad

- Do not install the operating table on an

uneven floor.

- Do not put a pad under the column base for

raising the table.
It may cause the table falling down and injury.

CAUTION

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands